Identifying a component with only a partial part number

The name of the pictureThe name of the pictureThe name of the pictureClash Royale CLAN TAG#URR8PPP











up vote
1
down vote

favorite












I have taken apart some circuitry that no longer works and I accidentally went a bit too far with the dremel. This means I've partially obscured the serial number of a component i'm wishing to identify.



Here is a picture:
enter image description here



There's 3 lines of text as far as I can see on the component in the centre.



  • The 1st being (I think) EL1738

  • 2nd NY135 (maybe)

  • 3rd SSU

I've tried punching these into google without much luck.



The device itself switches on a coil every other time a hall effect sensor is triggered. My first thoughts are that this might be some sort of flip flop.



What id like to know is what else can I do in order to identify this component?










share|improve this question



























    up vote
    1
    down vote

    favorite












    I have taken apart some circuitry that no longer works and I accidentally went a bit too far with the dremel. This means I've partially obscured the serial number of a component i'm wishing to identify.



    Here is a picture:
    enter image description here



    There's 3 lines of text as far as I can see on the component in the centre.



    • The 1st being (I think) EL1738

    • 2nd NY135 (maybe)

    • 3rd SSU

    I've tried punching these into google without much luck.



    The device itself switches on a coil every other time a hall effect sensor is triggered. My first thoughts are that this might be some sort of flip flop.



    What id like to know is what else can I do in order to identify this component?










    share|improve this question

























      up vote
      1
      down vote

      favorite









      up vote
      1
      down vote

      favorite











      I have taken apart some circuitry that no longer works and I accidentally went a bit too far with the dremel. This means I've partially obscured the serial number of a component i'm wishing to identify.



      Here is a picture:
      enter image description here



      There's 3 lines of text as far as I can see on the component in the centre.



      • The 1st being (I think) EL1738

      • 2nd NY135 (maybe)

      • 3rd SSU

      I've tried punching these into google without much luck.



      The device itself switches on a coil every other time a hall effect sensor is triggered. My first thoughts are that this might be some sort of flip flop.



      What id like to know is what else can I do in order to identify this component?










      share|improve this question















      I have taken apart some circuitry that no longer works and I accidentally went a bit too far with the dremel. This means I've partially obscured the serial number of a component i'm wishing to identify.



      Here is a picture:
      enter image description here



      There's 3 lines of text as far as I can see on the component in the centre.



      • The 1st being (I think) EL1738

      • 2nd NY135 (maybe)

      • 3rd SSU

      I've tried punching these into google without much luck.



      The device itself switches on a coil every other time a hall effect sensor is triggered. My first thoughts are that this might be some sort of flip flop.



      What id like to know is what else can I do in order to identify this component?







      identification flipflop






      share|improve this question















      share|improve this question













      share|improve this question




      share|improve this question








      edited 15 mins ago









      Passerby

      54.4k448142




      54.4k448142










      asked 2 hours ago









      Festivejelly

      1196




      1196




















          1 Answer
          1






          active

          oldest

          votes

















          up vote
          5
          down vote



          accepted










          That's most likely an ATMEL ATTINY13S -10SSU. (or -20SSU)



          It's a µC with integrated flash ROM. You had to read out that flash ROM (if enabled) to make a replacement part function at this place. A part off the shelf comes empty and will not function.






          share|improve this answer




















          • That makes sense to me actually. I could probably program it myself.
            – Festivejelly
            1 hour ago










          • Yeah, but you had to read out the flash ROM of the existing part first, so you have the program needed. Or you develop new software yourself.
            – Janka
            1 hour ago










          • I can develop the software myself. its a simple program needed to act as a flip flop. The only thing that doesnt quite fit are the pin outs. The top left is ground or VCC and the 2nd from the bottom left is ground or VCC which doesnt match up to the ATTINY 13
            – Festivejelly
            1 hour ago










          • See that tiny capacitor right next to the chip? That one connects Vdd and GND for a stable power supply at high switching speeds. One lead goes to pin 4, which matches the ATtiny13. Check where the other lead goes to.
            – Janka
            1 hour ago











          • I see now, Thats correct. Thanks for helping me ID this.
            – Festivejelly
            1 hour ago










          Your Answer




          StackExchange.ifUsing("editor", function ()
          return StackExchange.using("mathjaxEditing", function ()
          StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix)
          StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
          );
          );
          , "mathjax-editing");

          StackExchange.ifUsing("editor", function ()
          return StackExchange.using("schematics", function ()
          StackExchange.schematics.init();
          );
          , "cicuitlab");

          StackExchange.ready(function()
          var channelOptions =
          tags: "".split(" "),
          id: "135"
          ;
          initTagRenderer("".split(" "), "".split(" "), channelOptions);

          StackExchange.using("externalEditor", function()
          // Have to fire editor after snippets, if snippets enabled
          if (StackExchange.settings.snippets.snippetsEnabled)
          StackExchange.using("snippets", function()
          createEditor();
          );

          else
          createEditor();

          );

          function createEditor()
          StackExchange.prepareEditor(
          heartbeatType: 'answer',
          convertImagesToLinks: false,
          noModals: false,
          showLowRepImageUploadWarning: true,
          reputationToPostImages: null,
          bindNavPrevention: true,
          postfix: "",
          onDemand: true,
          discardSelector: ".discard-answer"
          ,immediatelyShowMarkdownHelp:true
          );



          );













           

          draft saved


          draft discarded


















          StackExchange.ready(
          function ()
          StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f399202%2fidentifying-a-component-with-only-a-partial-part-number%23new-answer', 'question_page');

          );

          Post as a guest






























          1 Answer
          1






          active

          oldest

          votes








          1 Answer
          1






          active

          oldest

          votes









          active

          oldest

          votes






          active

          oldest

          votes








          up vote
          5
          down vote



          accepted










          That's most likely an ATMEL ATTINY13S -10SSU. (or -20SSU)



          It's a µC with integrated flash ROM. You had to read out that flash ROM (if enabled) to make a replacement part function at this place. A part off the shelf comes empty and will not function.






          share|improve this answer




















          • That makes sense to me actually. I could probably program it myself.
            – Festivejelly
            1 hour ago










          • Yeah, but you had to read out the flash ROM of the existing part first, so you have the program needed. Or you develop new software yourself.
            – Janka
            1 hour ago










          • I can develop the software myself. its a simple program needed to act as a flip flop. The only thing that doesnt quite fit are the pin outs. The top left is ground or VCC and the 2nd from the bottom left is ground or VCC which doesnt match up to the ATTINY 13
            – Festivejelly
            1 hour ago










          • See that tiny capacitor right next to the chip? That one connects Vdd and GND for a stable power supply at high switching speeds. One lead goes to pin 4, which matches the ATtiny13. Check where the other lead goes to.
            – Janka
            1 hour ago











          • I see now, Thats correct. Thanks for helping me ID this.
            – Festivejelly
            1 hour ago














          up vote
          5
          down vote



          accepted










          That's most likely an ATMEL ATTINY13S -10SSU. (or -20SSU)



          It's a µC with integrated flash ROM. You had to read out that flash ROM (if enabled) to make a replacement part function at this place. A part off the shelf comes empty and will not function.






          share|improve this answer




















          • That makes sense to me actually. I could probably program it myself.
            – Festivejelly
            1 hour ago










          • Yeah, but you had to read out the flash ROM of the existing part first, so you have the program needed. Or you develop new software yourself.
            – Janka
            1 hour ago










          • I can develop the software myself. its a simple program needed to act as a flip flop. The only thing that doesnt quite fit are the pin outs. The top left is ground or VCC and the 2nd from the bottom left is ground or VCC which doesnt match up to the ATTINY 13
            – Festivejelly
            1 hour ago










          • See that tiny capacitor right next to the chip? That one connects Vdd and GND for a stable power supply at high switching speeds. One lead goes to pin 4, which matches the ATtiny13. Check where the other lead goes to.
            – Janka
            1 hour ago











          • I see now, Thats correct. Thanks for helping me ID this.
            – Festivejelly
            1 hour ago












          up vote
          5
          down vote



          accepted







          up vote
          5
          down vote



          accepted






          That's most likely an ATMEL ATTINY13S -10SSU. (or -20SSU)



          It's a µC with integrated flash ROM. You had to read out that flash ROM (if enabled) to make a replacement part function at this place. A part off the shelf comes empty and will not function.






          share|improve this answer












          That's most likely an ATMEL ATTINY13S -10SSU. (or -20SSU)



          It's a µC with integrated flash ROM. You had to read out that flash ROM (if enabled) to make a replacement part function at this place. A part off the shelf comes empty and will not function.







          share|improve this answer












          share|improve this answer



          share|improve this answer










          answered 2 hours ago









          Janka

          7,3321718




          7,3321718











          • That makes sense to me actually. I could probably program it myself.
            – Festivejelly
            1 hour ago










          • Yeah, but you had to read out the flash ROM of the existing part first, so you have the program needed. Or you develop new software yourself.
            – Janka
            1 hour ago










          • I can develop the software myself. its a simple program needed to act as a flip flop. The only thing that doesnt quite fit are the pin outs. The top left is ground or VCC and the 2nd from the bottom left is ground or VCC which doesnt match up to the ATTINY 13
            – Festivejelly
            1 hour ago










          • See that tiny capacitor right next to the chip? That one connects Vdd and GND for a stable power supply at high switching speeds. One lead goes to pin 4, which matches the ATtiny13. Check where the other lead goes to.
            – Janka
            1 hour ago











          • I see now, Thats correct. Thanks for helping me ID this.
            – Festivejelly
            1 hour ago
















          • That makes sense to me actually. I could probably program it myself.
            – Festivejelly
            1 hour ago










          • Yeah, but you had to read out the flash ROM of the existing part first, so you have the program needed. Or you develop new software yourself.
            – Janka
            1 hour ago










          • I can develop the software myself. its a simple program needed to act as a flip flop. The only thing that doesnt quite fit are the pin outs. The top left is ground or VCC and the 2nd from the bottom left is ground or VCC which doesnt match up to the ATTINY 13
            – Festivejelly
            1 hour ago










          • See that tiny capacitor right next to the chip? That one connects Vdd and GND for a stable power supply at high switching speeds. One lead goes to pin 4, which matches the ATtiny13. Check where the other lead goes to.
            – Janka
            1 hour ago











          • I see now, Thats correct. Thanks for helping me ID this.
            – Festivejelly
            1 hour ago















          That makes sense to me actually. I could probably program it myself.
          – Festivejelly
          1 hour ago




          That makes sense to me actually. I could probably program it myself.
          – Festivejelly
          1 hour ago












          Yeah, but you had to read out the flash ROM of the existing part first, so you have the program needed. Or you develop new software yourself.
          – Janka
          1 hour ago




          Yeah, but you had to read out the flash ROM of the existing part first, so you have the program needed. Or you develop new software yourself.
          – Janka
          1 hour ago












          I can develop the software myself. its a simple program needed to act as a flip flop. The only thing that doesnt quite fit are the pin outs. The top left is ground or VCC and the 2nd from the bottom left is ground or VCC which doesnt match up to the ATTINY 13
          – Festivejelly
          1 hour ago




          I can develop the software myself. its a simple program needed to act as a flip flop. The only thing that doesnt quite fit are the pin outs. The top left is ground or VCC and the 2nd from the bottom left is ground or VCC which doesnt match up to the ATTINY 13
          – Festivejelly
          1 hour ago












          See that tiny capacitor right next to the chip? That one connects Vdd and GND for a stable power supply at high switching speeds. One lead goes to pin 4, which matches the ATtiny13. Check where the other lead goes to.
          – Janka
          1 hour ago





          See that tiny capacitor right next to the chip? That one connects Vdd and GND for a stable power supply at high switching speeds. One lead goes to pin 4, which matches the ATtiny13. Check where the other lead goes to.
          – Janka
          1 hour ago













          I see now, Thats correct. Thanks for helping me ID this.
          – Festivejelly
          1 hour ago




          I see now, Thats correct. Thanks for helping me ID this.
          – Festivejelly
          1 hour ago

















           

          draft saved


          draft discarded















































           


          draft saved


          draft discarded














          StackExchange.ready(
          function ()
          StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f399202%2fidentifying-a-component-with-only-a-partial-part-number%23new-answer', 'question_page');

          );

          Post as a guest













































































          Comments

          Popular posts from this blog

          What does second last employer means? [closed]

          Installing NextGIS Connect into QGIS 3?

          One-line joke