Would it damage a tile saw if I used a a dimmer switch on it?

The name of the pictureThe name of the pictureThe name of the pictureClash Royale CLAN TAG#URR8PPP











up vote
1
down vote

favorite












It's a 10 inch Ridgid wet tile saw from home depot. I have a dimmer light switch, and I was hoping to use it to slow the saw down about half the regular speed.



Would doing this damage the motor or anything?










share|improve this question





















  • You need an induction motor controller for 1.5 HP but these tend to have poor speed load regulation so that’s why they invented VFD’s
    – Tony EE rocketscientist
    49 mins ago










  • Why would you want to reduce blade speed? Greater velocity should improve cuts for diamond or carbide abrasive blades.
    – K H
    44 mins ago














up vote
1
down vote

favorite












It's a 10 inch Ridgid wet tile saw from home depot. I have a dimmer light switch, and I was hoping to use it to slow the saw down about half the regular speed.



Would doing this damage the motor or anything?










share|improve this question





















  • You need an induction motor controller for 1.5 HP but these tend to have poor speed load regulation so that’s why they invented VFD’s
    – Tony EE rocketscientist
    49 mins ago










  • Why would you want to reduce blade speed? Greater velocity should improve cuts for diamond or carbide abrasive blades.
    – K H
    44 mins ago












up vote
1
down vote

favorite









up vote
1
down vote

favorite











It's a 10 inch Ridgid wet tile saw from home depot. I have a dimmer light switch, and I was hoping to use it to slow the saw down about half the regular speed.



Would doing this damage the motor or anything?










share|improve this question













It's a 10 inch Ridgid wet tile saw from home depot. I have a dimmer light switch, and I was hoping to use it to slow the saw down about half the regular speed.



Would doing this damage the motor or anything?







motor dimmer






share|improve this question













share|improve this question











share|improve this question




share|improve this question










asked 2 hours ago









geekman

516




516











  • You need an induction motor controller for 1.5 HP but these tend to have poor speed load regulation so that’s why they invented VFD’s
    – Tony EE rocketscientist
    49 mins ago










  • Why would you want to reduce blade speed? Greater velocity should improve cuts for diamond or carbide abrasive blades.
    – K H
    44 mins ago
















  • You need an induction motor controller for 1.5 HP but these tend to have poor speed load regulation so that’s why they invented VFD’s
    – Tony EE rocketscientist
    49 mins ago










  • Why would you want to reduce blade speed? Greater velocity should improve cuts for diamond or carbide abrasive blades.
    – K H
    44 mins ago















You need an induction motor controller for 1.5 HP but these tend to have poor speed load regulation so that’s why they invented VFD’s
– Tony EE rocketscientist
49 mins ago




You need an induction motor controller for 1.5 HP but these tend to have poor speed load regulation so that’s why they invented VFD’s
– Tony EE rocketscientist
49 mins ago












Why would you want to reduce blade speed? Greater velocity should improve cuts for diamond or carbide abrasive blades.
– K H
44 mins ago




Why would you want to reduce blade speed? Greater velocity should improve cuts for diamond or carbide abrasive blades.
– K H
44 mins ago










2 Answers
2






active

oldest

votes

















up vote
2
down vote



accepted










Most dimmer switches are rated 500 watts max and a 10" tile saw might be 1500 watts. The nominal current consumption of the motor is already three times the maximum of the dimmmer switch. Worst is the starting current of the motor can spike even 10 folds of the nominal. This will instantly destroy the triac in your dimmer switch.



Additional to this, motors are inductive loads which cause lots of problem with phase controlled lamp dimmers which are plainly made for the resistive load.



You probably have to look for higher power phase controlled chopper designed specifically for universal motors.






share|improve this answer



























    up vote
    2
    down vote













    Light dimmers are not meant to be used with inductive loads like motors. You will destroy it pretty quickly. You can buy dimmer/speed controllers that are meant for use with motors.



    The tile saw is almost certainly a series-wound motor which will work just fine with a triac speed controller.






    share|improve this answer




















      Your Answer




      StackExchange.ifUsing("editor", function ()
      return StackExchange.using("mathjaxEditing", function ()
      StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix)
      StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
      );
      );
      , "mathjax-editing");

      StackExchange.ifUsing("editor", function ()
      return StackExchange.using("schematics", function ()
      StackExchange.schematics.init();
      );
      , "cicuitlab");

      StackExchange.ready(function()
      var channelOptions =
      tags: "".split(" "),
      id: "135"
      ;
      initTagRenderer("".split(" "), "".split(" "), channelOptions);

      StackExchange.using("externalEditor", function()
      // Have to fire editor after snippets, if snippets enabled
      if (StackExchange.settings.snippets.snippetsEnabled)
      StackExchange.using("snippets", function()
      createEditor();
      );

      else
      createEditor();

      );

      function createEditor()
      StackExchange.prepareEditor(
      heartbeatType: 'answer',
      convertImagesToLinks: false,
      noModals: false,
      showLowRepImageUploadWarning: true,
      reputationToPostImages: null,
      bindNavPrevention: true,
      postfix: "",
      onDemand: true,
      discardSelector: ".discard-answer"
      ,immediatelyShowMarkdownHelp:true
      );



      );













       

      draft saved


      draft discarded


















      StackExchange.ready(
      function ()
      StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f399766%2fwould-it-damage-a-tile-saw-if-i-used-a-a-dimmer-switch-on-it%23new-answer', 'question_page');

      );

      Post as a guest






























      2 Answers
      2






      active

      oldest

      votes








      2 Answers
      2






      active

      oldest

      votes









      active

      oldest

      votes






      active

      oldest

      votes








      up vote
      2
      down vote



      accepted










      Most dimmer switches are rated 500 watts max and a 10" tile saw might be 1500 watts. The nominal current consumption of the motor is already three times the maximum of the dimmmer switch. Worst is the starting current of the motor can spike even 10 folds of the nominal. This will instantly destroy the triac in your dimmer switch.



      Additional to this, motors are inductive loads which cause lots of problem with phase controlled lamp dimmers which are plainly made for the resistive load.



      You probably have to look for higher power phase controlled chopper designed specifically for universal motors.






      share|improve this answer
























        up vote
        2
        down vote



        accepted










        Most dimmer switches are rated 500 watts max and a 10" tile saw might be 1500 watts. The nominal current consumption of the motor is already three times the maximum of the dimmmer switch. Worst is the starting current of the motor can spike even 10 folds of the nominal. This will instantly destroy the triac in your dimmer switch.



        Additional to this, motors are inductive loads which cause lots of problem with phase controlled lamp dimmers which are plainly made for the resistive load.



        You probably have to look for higher power phase controlled chopper designed specifically for universal motors.






        share|improve this answer






















          up vote
          2
          down vote



          accepted







          up vote
          2
          down vote



          accepted






          Most dimmer switches are rated 500 watts max and a 10" tile saw might be 1500 watts. The nominal current consumption of the motor is already three times the maximum of the dimmmer switch. Worst is the starting current of the motor can spike even 10 folds of the nominal. This will instantly destroy the triac in your dimmer switch.



          Additional to this, motors are inductive loads which cause lots of problem with phase controlled lamp dimmers which are plainly made for the resistive load.



          You probably have to look for higher power phase controlled chopper designed specifically for universal motors.






          share|improve this answer












          Most dimmer switches are rated 500 watts max and a 10" tile saw might be 1500 watts. The nominal current consumption of the motor is already three times the maximum of the dimmmer switch. Worst is the starting current of the motor can spike even 10 folds of the nominal. This will instantly destroy the triac in your dimmer switch.



          Additional to this, motors are inductive loads which cause lots of problem with phase controlled lamp dimmers which are plainly made for the resistive load.



          You probably have to look for higher power phase controlled chopper designed specifically for universal motors.







          share|improve this answer












          share|improve this answer



          share|improve this answer










          answered 1 hour ago









          soosai steven

          1,2421510




          1,2421510






















              up vote
              2
              down vote













              Light dimmers are not meant to be used with inductive loads like motors. You will destroy it pretty quickly. You can buy dimmer/speed controllers that are meant for use with motors.



              The tile saw is almost certainly a series-wound motor which will work just fine with a triac speed controller.






              share|improve this answer
























                up vote
                2
                down vote













                Light dimmers are not meant to be used with inductive loads like motors. You will destroy it pretty quickly. You can buy dimmer/speed controllers that are meant for use with motors.



                The tile saw is almost certainly a series-wound motor which will work just fine with a triac speed controller.






                share|improve this answer






















                  up vote
                  2
                  down vote










                  up vote
                  2
                  down vote









                  Light dimmers are not meant to be used with inductive loads like motors. You will destroy it pretty quickly. You can buy dimmer/speed controllers that are meant for use with motors.



                  The tile saw is almost certainly a series-wound motor which will work just fine with a triac speed controller.






                  share|improve this answer












                  Light dimmers are not meant to be used with inductive loads like motors. You will destroy it pretty quickly. You can buy dimmer/speed controllers that are meant for use with motors.



                  The tile saw is almost certainly a series-wound motor which will work just fine with a triac speed controller.







                  share|improve this answer












                  share|improve this answer



                  share|improve this answer










                  answered 1 hour ago









                  τεκ

                  3,13011016




                  3,13011016



























                       

                      draft saved


                      draft discarded















































                       


                      draft saved


                      draft discarded














                      StackExchange.ready(
                      function ()
                      StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f399766%2fwould-it-damage-a-tile-saw-if-i-used-a-a-dimmer-switch-on-it%23new-answer', 'question_page');

                      );

                      Post as a guest













































































                      Comments

                      Popular posts from this blog

                      What does second last employer means? [closed]

                      Installing NextGIS Connect into QGIS 3?

                      One-line joke